Autowatch Ghost Immobiliser Installation
The Ghost is the UK's most advanced aftermarket CAN bus immobiliser. It's discreet and does not have LED indicators or key fobs and is hidden in the vehicle's wiring.
The user can also disable the system for a short period of time by using Transport Mode when renting their car. This guide will take you through the steps of installing a Ghost immobiliser.
Professional Installation
The Autowatch Ghost immobiliser is a advanced security device that safeguards your vehicle against hacking, key cloning, and relay attacks. The system is directly connected to the ECU of your vehicle and protected by a PIN code you select. It's undetectable to thieves using diagnostic scanners or other modern methods, and it is unable to be disabled through circuit cuts.
The system is easy to use, but it is essential to have a professional installation to ensure a smooth and secure connection to your vehicle's ECU. Installers who are approved by Thatcham can assist you with the installation and programing of your Ghost system. They can also recommend an alarm or tracking system to complete the security package for your vehicle.
To avoid ghost 2 immobiliser cost of short circuits or airbags To avoid an accidental deployment of airbags or short circuits, the installer must remove your battery. Once the battery is disconnected, the installer may start working safely. Basic hand tools are helpful for making precise connections, while a multimeter can be used to test electrical values and safety. Insulation tape and cable ties are also vital for protecting connections and keeping wiring tidy. In addition, the user's manual gives specific guidelines that are specifically tailored to your Ghost Immobiliser model.
During the installation, it is essential to choose a grounding point that's free of paint and debris. The installer should ensure that the immobiliser's CAN H and CAN L wires are connected to the correct ports on the vehicle's ECU. These wires can be connected or soldered depending on the model. To ensure a secure and long-lasting connection, it is recommended that you choose a high-quality plug.
Transport Mode can be activated by the customer once the installation is completed. This allows valet parking or mechanics to access the vehicle without having to know the pin code. To accomplish this, the customer has to hit the button for service on the dashboard five times within 2 seconds. After that, the system will confirm with 5 signal indicators.
The Autowatch Ghost 2 is a highly effective immobiliser that's TASSA certified and Thatcham approved. It's an excellent choice for those who rent out their vehicles regularly on platforms like Turo. An immobiliser can cut down on insurance rates, as it decreases the likelihood of theft.
Getting Started
It's not difficult to come up with an autowatch immobiliser for those who want to safeguard your car from thieves. The device prevents your vehicle from starting if someone steals or copies your key. This is due to its advanced technology, which is designed to prevent the car's engine from starting without the correct PIN code is entered.
The device connects to the vehicle's bus network, CAN, allowing direct communication with the ECU. It makes use of the buttons on your dashboard and steering to create a unique sequence which only you are aware of. This makes it impossible for anyone else to start your car. This is the best security system to protect your pride and joy, keeping its value intact in the event that you decide to sell it in the future.
Installing a ghost immobiliser is a simple process, but it is crucial to follow the steps carefully to avoid issues with electricity and system malfunctions. First, you must locate and identify a constant 12V power source as well as a good grounding point on the vehicle's chassis. After that, you are able to begin connecting the wires to the immobiliser. Make sure to use high-quality connectors and soldering techniques to ensure a secure connection. Insulate the connections using heat shrink tubing or insulation tape, or other materials to prevent short circuits in electrical power.
Once the wires have been connected, you can connect the battery and begin the engine to check whether the immobiliser is functioning. Once everything is working properly then you can put it in a secure place beneath the dash or anywhere else in the vehicle. Make sure to cover it in a secure manner to ensure that thieves cannot tamper with it.
The Ghost 2 immobiliser has been TASSA (Tracker and Aftermarket Security System Association) that means it is a high-quality deterrent to car burglars. It is resistant to hacking and key cloning and is not able to be disabled without the code. The device is easy to use, and it can be set into the service valet setting to ensure that your vehicle will not be activated if you take it to an MOT or for servicing.
Wiring
The Ghost Immobiliser is a cutting-edge security system designed to stop theft of vehicles. It communicates with your vehicle's ECU and connects directly to its CAN bus. The Ghost Immobiliser will not interfere with the factory settings of your car unlike other aftermarket systems which require the removal of circuit elements.
The system is also undetectable by thieves using diagnostic scanners. This is because the system doesn't send and receive radio frequency signals, and it relies on CAN data to communicate with your ECU. In addition, it doesn't need any modifications to your vehicle's existing key fobs.
Enter your sequence for disarming (either two or one button) and then turn on the ignition of your vehicle to activate the Ghost Immobiliser. The indicator will flash two times to confirm that you've entered the correct code. After that, you are able to start your vehicle and drive off in peace.
Once installed, the Ghost Immobiliser safeguards your vehicle against key cloning or hacking while protecting its value. In Transport Mode, you can temporarily disable the Ghost Immobiliser in case you need to give your car over for service or valet parking.
To complete the Ghost Immobiliser installation, you'll have to locate an energy source that is constant (12V) and a grounding point. Make sure that both are well-insulated and able to be touched. Cable ties are also recommended for bundling and secure the wires. This reduces the possibility of theft by thieves. To avoid committing mistakes, double-check these points and mark them using labels or tape. It's recommended to inspect every connection for signs of wear and tear. Make sure all connections are firmly in place and properly sealed. Also, don't forget test the Ghost Immobiliser after the installation is complete. This will confirm that the unit is operating properly and that all connections and insulation are safe. Be sure to correct any issues as soon as they arise.
Testing
The Autowatch Ghost immobiliser is an innovative vehicle security system that connects seamlessly with your car's ECU to stop unauthorised motor starting. Its innovative technology safeguards your vehicle from hacking and key cloning along with other methods commonly employed by thieves to steal vehicles. The Ghost is also able to work in conjunction with other alarm and tracking systems to give the most complete protection for your vehicle. The Ghost's unparalleled features and secluded design make it a preferred choice for car lovers and security-conscious drivers alike.
To ensure the proper integration of the Ghost Immobiliser, you must to follow all steps of the installation process. A good starting point is to consult the vehicle's wiring diagram that will serve as a guideline for locating and connecting the required wires. The next step is to determine the grounding and power sources. Once you've identified these, you'll have to mark them in a way that they're easily identifiable during the installation process. It's important to use high-quality materials and tools. Hand tools are essential to help you make precise connections. A multimeter can verify electrical values, and also ensure safety. Cable ties and insulation tape can help keep connections neat and tidy. A Ghost-specific user manual is also available.
It is important to test the system prior installing it. Enter the PIN code into the system and then start the vehicle. This test will verify that the immobiliser works as intended and prevent unauthorised vehicle starts. It's recommended to perform this routinely as part of your regular vehicle inspections to ensure that the system is operating properly.
After the installation has been completed, you can start driving your vehicle with confidence. The Ghost will help keep your car and its contents safe from would-be thieves, ensuring that nobody can take off with your vehicle without the correct PIN. The Ghost can also be paired with a tracker that is approved by Thatcham to detect any attempts at tampering or theft that could lead to the location of your vehicle if it's stolen.
The Ghost can be utilized in a variety of vehicles and is compatible with all major brands. Monty's Locksmith can assist you in securing your vehicle with this innovative device. Contact us today to learn more about our services and installation options. We are a TASSA registered installer, a certificate that guarantees we follow strict standards for installing our products. This ensures customers insurance companies, customers, and law enforcement agencies that installations are done safely and in a safe manner.